LABORATORYWARE

Biology | Electricity & Magnetism | Heat | Light | Mechanics | Sound

Laboratoryware | Porcelainware | Glassware| Online Store

<Prev | Next>

 TEST TUBE RACK, POLYPROPYLENE

 

Replacement for wood and metal racks. For six test tubes.

Has six openings of 25mm diameter on top plate, with hemispherical wells and drying pins. Open side for clear viewing. Can be easily assembled. Dimensions: (l x w x h), 240 x 70 x 90mm.

Cat. No.

2035-01


 TEST TUBE RACK, ABS POLYMER

 

A 12 place rack for tubes up to 25mm in diameter. Three tier design measures (l x w x h), 225 x 125 x 70mm. The lower plate has rounded wells with drain holes. Convenient hand grips on both sides.

Cat. No.

2035-11


 TEST TUBE RACK, ABS POLYMER

 

A 20 tube rack for tubes up to 19mm in diameter. Three tier design measures (l x w x h), 325 x 125 x 70mm. The lower plate has rounded wells with drain holes. Convenient hand grips on both sides.

Cat. No.

2035-12


 TEST TUBE RACK, ABS POLYMER

 

A 31 tube rack for tubes up to 12mm in diameter. Three tier design measures (l x w x h), 275 x 110 x 65mm. The lower plate has rounded wells with drain holes. Convenient hand grips on both sides.

Cat. No.

2035-13


 TEST TUBE SUPPORT, WOODEN, SIX PLACES

 

Made of kiln dried wood. Has six openings of 24mm diameter and six drying pins. Measures (l x w x h), 240 x 70 x 90mm. Oil finished.

Cat. No.

2035-21


 TEST TUBE SUPPORT, WOODEN, TWELVE PLACES

 

Has twelve openings of 20mm diameter. Measures (l x w x h), 200 x 140 x 70mm. Made of kiln dried wood. Oil finished.

Cat. No.

2035-22


 SUPPORT RINGS, CAST IRON

 

For use on support rods, lattices etc., upto 13mm ( 1/2in) diameter.

With integral bossheads. Distance from center of ring to center of bosshead is 10.5cm (4 1/4in). Brass thumbscrew. Enamel finish.

Ring i.d.

Cat. No.

50mm (2in)

2038-01

62mm (2 1/2in)

2038-02

75mm (3in)

2038-03

100mm (4in)

2038-04

125mm (5in)

2038-05


 SUPPORT PLATE (TABLE/SHELF) WITH CLAMP

 

Consists of a flat circular cast iron plate with integral bosshead and plated thumbscrew. Inside diameter of the rim 127mm (5in). Can be clamped to rods up to 16mm diameter.

Cat. No.

2040-00


 SUPPORT RINGS, EXTENSION (PLAIN EXTENSION RINGS)

 

For use with clamp holders.

Made of zinc plated steel wire of diameter 8mm ( 5/16in), and with shank about 30cm (12in) long. Approximate ring diameters are:

Ring i.d.

Cat. No.

50mm (2in)

2042-01

75mm (3in)

2042-02

100mm (4in)

2042-03

125mm (5in)

2042-04

150mm (6in)

2042-05


 SLOTTED BASE

 

For holding flat object upright.

Cast iron, enamelled base with steel thumbscrew. Distance between the jaws is 3.4cm and the height of the jaw is 4cm. Dimensions: (l x w), 9.5 x 7.5cm.

Cat. No.

2043-00


<Prev | Top | Next>